Don R. Crawley, Linux+ and CCNA-certified, is president and chief technologist at soundtraining.net, the Seattle training firm specializing in accelerated, task-oriented training for IT professionals. He works with IT pros to enhance their work, lives, and careers. For more information about learning opportunities with soundtraining.net, visit here.
Copyright (c) 2008 Don R. Crawley
Ethernet was developed at Xerox's Palo Alto Research Center (PARC) by Robert Metcalfe and David Boggs with Chuck Thacker and Butler Lampson in the early 1970s. Xerox filed a patent application for Ethernet in 1975. Today, Ethernet is based on IEEE standard 802.3 (Institute of Electrical and Electronic Engineers). Metcalfe left Xerox in 1979 and founded 3Com to promote local area networks and personal computers. He persuaded Digital Equipment Corporation (DEC) and Intel to work together with Xerox to promote the DIX (Digital/Intel/Xerox) Ethernet standard. Ethernet is named for the invisible, massless substance that 19th century scientists believed filled the universe. Ethernet was originally based on the same rules as those for polite conversation. Each computer wanting to transmit data waits until there's a lull in network traffic before attempting to transmit its data. That technology was called CSMA/CD for Carrier Sense Multiple Access Collision Detection and used coaxial cables as a transmission medium. Today, Ethernet uses full duplex transmission over unshielded twisted pair copper cables or fiber optic cables with a system of hubs and/or switches.
Ethernet operates at layer two of the OSI reference model. Layer two, also known as the Data Link Layer, is subdivided into the Logical Link Control (LLC) layer and the Media Access Control (MAC) layer. Ethernet nodes use a globally-unique 48-bit address called the MAC address to communicate within a network. Datagrams at layer two are called frames. The frame structure used by modern Ethernet is the same as that used by earlier coaxial-cabled Ethernet networks, thus providing a level of backwards compatibility.
The original Ethernet operated at a speed of three megabits per second. Today, typical transmission rates for Ethernet are 10 Mbps, 100 Mbps, and 1000 Mbps (Gigabit Ethernet). 10,000 Mbps (10 Gigabit Ethernet) is now starting to emerge. Faster data rates are always under development.
Ethernet Cable Standards
10-Base-2, also known as thinnet, uses coaxial cable, is limited to 10 Mbps, and a maximum segment length of 185 meters. 10-Base 2 is falling into disuse due to the lower cost and greater simplicity associated with UTP (unshielded twisted pair) cabling.
10-Base-5, also known as thicknet, uses coaxial cable, is limited to 10 Mbps, and a maximum segment length of 500 meters. 10-Base-5 is rarely seen anymore.
10-Base-T uses unshielded twisted pair (UTP) cable over a maximum of 100 meters (328 feet) at a data rate of 10 Mbps. 10-Base-T uses only two of the four wire pairs in the cable.
10-Base-FL uses fiber optic lines up to 2000 meters with a maximum data rate of 10 Mbps.
100-Base-TX uses UTP cable over a maximum segment length of 100 meters with a maximum data rate of 100 Mbps. 100-Base-TX also uses only two of the four wire pairs in the cable.
100-Base-FX uses fiber optic cable over a maximum segment length of 2000 meters with a maximum data rate of 100 Mbps.
1000-Base-FX uses fiber optic cable over a maximum segment length of 2000 meters with a maximum data rate of 1000 Mbps (one gigabit per second).
1000-Base-TX uses UTP cable cable over a maximum segment length of 100 meters with a maximum data rate of 1000 Mbps (one gigabit per second). Unlike 100-Base-TX, 1000-Base-TX uses all four wire pairs in the cable.
Copper Cable Categories
Although there are a total of nine categories of unshielded twisted pair (UTP) copper cable, there are really only three that you're likely to encounter in your local area network. The others are either obsolete or designed for use in backbone networks. The three categories are:
Category 5e: Provides performance of up to 100 MHz, and is frequently used for both 100 Mbit/s and Gigabit Ethernet networks.
Category 6: Provides performance of up to 250 MHz, more than double category 5 and 5e.
Category 6a: Provides performance of up to 500 MHz, double that of category 6 and is even suitable for 10 Gigabit Ethernet networks.
What should you use in your network?
Build your networks with the fastest cable you can afford. Your bandwidth demands will increase over time and retro-fitting your cable plant is disruptive, time-consuming, and expensive.
Ethernet was developed at Xerox's Palo Alto Research Center (PARC) by Robert Metcalfe and David Boggs with Chuck Thacker and Butler Lampson in the early 1970s. Xerox filed a patent application for Ethernet in 1975. Today, Ethernet is based on IEEE standard 802.3 (Institute of Electrical and Electronic Engineers). Metcalfe left Xerox in 1979 and founded 3Com to promote local area networks and personal computers. He persuaded Digital Equipment Corporation (DEC) and Intel to work together with Xerox to promote the DIX (Digital/Intel/Xerox) Ethernet standard. Ethernet is named for the invisible, massless substance that 19th century scientists believed filled the universe. Ethernet was originally based on the same rules as those for polite conversation. Each computer wanting to transmit data waits until there's a lull in network traffic before attempting to transmit its data. That technology was called CSMA/CD for Carrier Sense Multiple Access Collision Detection and used coaxial cables as a transmission medium. Today, Ethernet uses full duplex transmission over unshielded twisted pair copper cables or fiber optic cables with a system of hubs and/or switches.
Ethernet operates at layer two of the OSI reference model. Layer two, also known as the Data Link Layer, is subdivided into the Logical Link Control (LLC) layer and the Media Access Control (MAC) layer. Ethernet nodes use a globally-unique 48-bit address called the MAC address to communicate within a network. Datagrams at layer two are called frames. The frame structure used by modern Ethernet is the same as that used by earlier coaxial-cabled Ethernet networks, thus providing a level of backwards compatibility.
The original Ethernet operated at a speed of three megabits per second. Today, typical transmission rates for Ethernet are 10 Mbps, 100 Mbps, and 1000 Mbps (Gigabit Ethernet). 10,000 Mbps (10 Gigabit Ethernet) is now starting to emerge. Faster data rates are always under development.
Ethernet Cable Standards
10-Base-2, also known as thinnet, uses coaxial cable, is limited to 10 Mbps, and a maximum segment length of 185 meters. 10-Base 2 is falling into disuse due to the lower cost and greater simplicity associated with UTP (unshielded twisted pair) cabling.
10-Base-5, also known as thicknet, uses coaxial cable, is limited to 10 Mbps, and a maximum segment length of 500 meters. 10-Base-5 is rarely seen anymore.
10-Base-T uses unshielded twisted pair (UTP) cable over a maximum of 100 meters (328 feet) at a data rate of 10 Mbps. 10-Base-T uses only two of the four wire pairs in the cable.
10-Base-FL uses fiber optic lines up to 2000 meters with a maximum data rate of 10 Mbps.
100-Base-TX uses UTP cable over a maximum segment length of 100 meters with a maximum data rate of 100 Mbps. 100-Base-TX also uses only two of the four wire pairs in the cable.
100-Base-FX uses fiber optic cable over a maximum segment length of 2000 meters with a maximum data rate of 100 Mbps.
1000-Base-FX uses fiber optic cable over a maximum segment length of 2000 meters with a maximum data rate of 1000 Mbps (one gigabit per second).
1000-Base-TX uses UTP cable cable over a maximum segment length of 100 meters with a maximum data rate of 1000 Mbps (one gigabit per second). Unlike 100-Base-TX, 1000-Base-TX uses all four wire pairs in the cable.
Copper Cable Categories
Although there are a total of nine categories of unshielded twisted pair (UTP) copper cable, there are really only three that you're likely to encounter in your local area network. The others are either obsolete or designed for use in backbone networks. The three categories are:
Category 5e: Provides performance of up to 100 MHz, and is frequently used for both 100 Mbit/s and Gigabit Ethernet networks.
Category 6: Provides performance of up to 250 MHz, more than double category 5 and 5e.
Category 6a: Provides performance of up to 500 MHz, double that of category 6 and is even suitable for 10 Gigabit Ethernet networks.
What should you use in your network?
Build your networks with the fastest cable you can afford. Your bandwidth demands will increase over time and retro-fitting your cable plant is disruptive, time-consuming, and expensive.
- Related Videos
- Related Articles
- Ask / Related Q&A
- How can i extend my Ethernet LAN cable Networking & Security
- NETWORK CABLING
- Cabling Installation Options for Your Small Business Clients
- Ethernet cable- most economical networking solution
- Category 7 cable
- Useful Information on Data Cabling
- Understanding the Fundamentals of Ethernet
- How to Obtain a Cable Modem Connection
Remote IT Support Helps Business Control Costs
By: Dave Talbot | 16/11/2009Business downtime can be very costly especially for small business who cannot afford to have an onsite computer repair technician available throughout the day. This article explores the benefits of remote IT support for small and large corporations.
The Secret To Solving PC Problems On Your Own
By: Sayid Jarrah | 16/11/2009The secret to computing happiness is to understand that most computer problems are software-related and can be solved on your own. All you need to do to take care of these problems is a little time, patience and a few guidelines. In this article are some of the basic guidelines that will help you in solving PC problems.
Solving PC Errors: Not Just For Computer Experts
By: Sayid Jarrah | 16/11/2009PC users all across the world have realized that solving common PC errors is not as difficult as they once thought. And by following the necessary maintenance activities and deploying the right protective software you can safely keep common errors at bay. Discussed in this article are some common causes of computer errors and the steps you can perform to efficiently fix computer errors.
The Truth Behind Computer Errors And How You Can Resolve Them
By: Sayid Jarrah | 16/11/2009Thanks to the information wave generated by the internet these days, more and more computer users are waking up to the truth that with a little basic computer knowledge they can resolve and prevent PC problems themselves. You can become a computer expert yourself and resolve some of the most common computer errors by following the simple troubleshooting steps given in this article.
Can You Really Increase Computer Speed and Make Your PC Like New?
By: Sayid Jarrah | 16/11/2009It is important for all PC users to try and optimize their computer’s performance by carrying out regular PC maintenance activities. This will not only keep your PC at its best performance, but will also increase the life of your computer by many years by keeping many computer problems at bay. This, in turn, will help you in improving your productivity and save money that you would otherwise would have spent in taking expert guidance to troubleshoot computer errors.
Be Your Own Computer Technician And Save Yourself Time And Money
By: Sayid Jarrah | 16/11/2009Today, all PC users can be computer technicians to the extent that they can take care of their day-to-day computer issues on their own. PC users can also solve a majority of computer problems associated with software, files and applications themselves. This article teaches you how to be your own computer technician and save yourself some time and money.
Getting really stylish? Get some fantastic LG VU skins, LG Venus skins and LG shine skins
By: BhratBrij | 16/11/2009If you are interested in getting the perfect skins for your LG Dare, LG VU, LG Venus or LG shine, you can get them easily on the Internet or in the nearest market.
Using Hands-Free Mobile Phone Accessories
By: Adriana N. | 16/11/2009The increasing use of cell phones while driving has become a serious safety concern. A recently released study by the Virginia Tech Transportation Institute found that "80% of traffic accidents are caused by driver distraction and young drivers were four times more likely to be involved in a crash." The...
How to Configure Ssh (secure Shell) for Remote Login on a Cisco Router
By: Don R. Crawley | 02/12/2008 | ComputersLearn how to configure SSH for secure remote login on a Cisco router in this soundtraining.net "how-to" guide. SSH replaces the notoriously non-secure Telnet protocol for remote login.
Understanding the Fundamentals of Ethernet
By: Don R. Crawley | 06/09/2008 | ComputersIn this brief article, you'll learn the basics of how Ethernet works in modern computer networks and cabling options for your network.
How to Get Help in Linux
By: Don R. Crawley | 04/09/2008 | ComputersThe Linux operating system includes substantial built-in help systems. In this article, veteran I.T. guy Don R. Crawley explains how to find and use Linux help systems.
The Three Secrets to Profitable Email Marketing
By: Don R. Crawley | 21/05/2008 | BusinessLegitimate email marketing is a very powerful tool for your business...if you use it correctly. In this concise article, you'll learn the three keys for profitable email marketing and how you can use it successfully in your business.
How to Create and Manage Access-control Lists on Cisco Asa and Pix Firewalls
By: Don R. Crawley | 30/04/2008 | ComputersLearn the fundamentals of building and managing access-control lists on a Cisco ASA or PIX firewall in this soundtraining.net "How-to" guide.
How to Create and Exchange Digital Documents
By: Don R. Crawley | 27/04/2008 | BusinessDigital documents are safer, more secure, easier to search, easier to send, and infinitely easier to store. In this article, you'll learn about the benefits of using digital documents and gain some practical ideas about how to start using digital documents in your business.
Automating Appointment Scheduling
By: Don R. Crawley | 24/04/2008 | BusinessLearn how to let your customers and clients manage their own appointments by automating the appointment scheduling process with free or low cost online tools. In this brief article, automation evangelist Don R. Crawley show you how to automate appointment scheduling with another way to go digital without going postal.